• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

The majority of homeowners can fix hinges that are loose. However, if the screw holes are damaged and won't hold screws you might need to use wood glue and dowels before you can put back the hinge.

Remove any surface rust. This will aid in keeping the dowels in place and give them an adequate base for them to rest on.

Eliminating the Hinges

Many standard door hinges can be removed, which makes it easier to move the door from one end of the frame to the other side or remove the entire door if necessary. It is simple for anyone with a bit of patience, although you have to know how to do it right.

If the hinges have been painted it is necessary to remove it before you attempt to remove the pins. If you do not, the paint may peel off and scratch your repair door frame hinge side when you attempt to lift it. Place the hinges into an stainless steel pot and fill it with water to the point that the hinges are submerged. The hinges should remain in the pan for around 30 minutes. The heat from the water will soften the paint making it easier to remove.

Once the pins are loosened and the pins are loose, you can take off the hinges from the frame and door. You can use a screwdriver to get the job done, but it is recommended that you use a magnetic screwdriver for this project. This type of screwdriver is specifically designed to take out metal screws and will help you get the job accomplished much faster.

It is a good idea to spray lubricant on the hinges prior to attempting to remove them. A simple lubricant will help the process to go more quickly and make it easier to remove the pins and screws. This kind of lubricant is able to be found in most hardware stores and home improvement stores.

Keep in mind that the number of door hinges you'll require will vary depending on the kind of door and the settings. Heavier and solid-cored doors will require more hinges whereas hollow-cored and lighter upvc doors hinges might only need two or three.

It is also important to be aware of the various kinds of hinges in order to determine which ones will be the most effective for your particular situation. Exterior hinges are generally designed to support the weight of the door, while interior hinges will need to be able to handle lighter loads.

Reattaching the Hinges

Sometimes, the hinges on doors loosen over time and start to hang in a crooked manner or slide. This can be a problem but is usually easy to solve. A simple retightening will usually resolve the issue. If the screw holes have been stripped out, it can be difficult to Fix Door Hinge. Fortunately, there is a trick to get these holes back to their original size that utilizes a wood dowel.

Begin by drilling out the hole from the previous one using a drill bit that is similar to the size of the new screw (typically 3/8"). Fill in the hole with wood glue and a wooden stick. To ensure a secure fit, the dowel must be cut at the same length as the screw. After that, reinstall the screw and tighten it to the desired level of tightness. If the door is still unable to be bounded up, add another dowel into the gap. Repeat the process. Close the door slowly after each adjustment to make sure that the clearances around the perimeter are correct.

Another option is to just use a wood plug instead of dowel. This will work equally well, but may take a bit longer to set up. You can use a piece of wood that has been whittled down to the proper size. If you don't have a tool for woodworking, you can also use toothpicks or wooden matches as well.

Use a countersink to make the hole smaller for the head of the screw after you have reinstalled it. This will prevent the screw from rubbing against the edges of the doors as they are opened and closed. This will make it easier to tighten the screws after installing hinges.

After you have reinstalled the hinge, make sure to grease it with a dry lubricant in order to ensure that it doesn't get stuck in the future. You can use products like PB Blaster and Liquid Wrench. You should apply a light coat handles and hinges allow it to take around 15 minutes to fully reach the barrel of the hinge.

Refinishing the Hinges

If you're not ready to replace the hinges on your door, you are able to make a few minor repairs. Check that the screws that attach the hinge plate in place to the door frame and frame are tight. If they're loose, tighten them with an electric drill or screwdriver. Be careful not to tighten your screws to the point that they create gaps at the trim joints or, even more damagingly remove the threads.

If the issue is that the hinge plates are separating, you can reattach the plates by applying wood glue on the side of them and inserting toothpicks or wooden dowels into the holes. Dowels and toothpicks create a solid foundation for the screws, which will stop the plates from moving as you push them in. Let the glue dry before attaching the hinge.

Another reason that causes loose hinges is that screws are worn out or missing. You can fix this problem by replacing the screws with larger ones. Use a drill bit that is exactly the same size as the screw hole to avoid drilling into the hinge or jamb.

After you've reattached your hinge close the door and look at the gap between the door and the frame. The gap should be about the thickness of a penny or less if the old door was hung incorrectly. If the hinges were installed properly, this shouldn't be an issue.

If the hinges are still loose, you could add a stronger window hinge repair between the hinge plate's surface and the mounting surface. This will give the hinges more room. You could also try removing the hinge pin from the troublesome hinge and pounding it using a hammer to make it tighter or use an entirely new hinge pin. You can also lubricate the hinges with mineral or jojoba oil to lessen friction and aid in holding their place. Lubricating your hinges periodically will help stop them from becoming stiff and squeaky, and also extend their lifespan.

Cleaning the Hinges

The continuous movement of hinges creates friction, which attracts dust particles. These particles may get stuck and accumulate in the moving parts of door hinges if they are not cleaned and lubricated regularly. As a result the hinge becomes stiff and creaky and its appearance could be damaged quickly. Regular cleaning, lubrication, and inspection can help preserve the quality of hinge on a door and ensure its proper operation.

Inspect the hinges to see how much rust has formed on their surfaces. If the rust is so bad that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace them. If you're able to save the hinges, remove any loose rust using wire brush and steel wool. Apply a commercial rust removal solution or homemade solution like lemon juice on the hinge. Allow the rust remover to sit on the hinge for several minutes to penetrate and dissolve any remaining corrosion.

If you don't want to spend the cost and time to replace your hinges, simply retightening the screws will bring back the hinge's functionality. If you have stripped the screw holes however, it could be necessary to attach the dowel of wood or shim to the hinge. Dowels made of wood are square pieces of wood that are in the form of rods that are available in different lengths and diameters. You can find them at home improvement stores as well as woodworking supply and craft shops, or on the internet.

A shim may be made of a piece of metal or plastic, depending on the kind of hinge you have. To make a dowel cut a piece of wooden dowel or any other durable material to the size you want. You can then dip the dowel in a glue for carpenters and then insert it into the stripped hole and let the glue hold the dowel in the right position.

Before cleaning the hinges, put down a paper cloth or towel to shield your flooring from spills. After securing the area then clean the hinges using a soft sponge or a cloth dipped into mild cleaner to eliminate dirt, grime, and tarnish. You can use a toothbrush or small brush to get into difficult-to-reach areas in tight spaces and crevices.