• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Why is My Car Ignition Locked?

There are many reasons your ignition might be stuck. The key could be dirty or have a broken wafer in it. This can be corrected by sliding the key in and out of the cylinder several times.

Another possibility is that the pins inside the lock cylinder are stuck. You could tap the cylinder lightly using a small tack-hammer.

Check the Battery

The shifter switch on the transmission may be malfunctioning when the car is in Park neutral or will not start when the key is switched on. It is possible to fix the issue by moving the gear shifter up or down to get the car into the correct gear.

If it's not turning, the issue may be with the neutral safety switch or the transmission shifter cable. A mechanic or local auto locksmith can easily solve these issues.

The ignition cylinder could also be worn out. Over time, the ignition and the key will wear out, which causes them to become difficult to insert or remove. A lubricant such as silicon lock grease can solve this issue, letting wafers slide into place.

Lint from your pocket and adhesive from tapes that hold packages together can build up on the key, which prevents it from sliding into the ignition. To fix this issue, you can try cleaning the key with a cloth or using a cleaner like Triflow. You should also utilize a spare key in order to see if the problem is related to the key or the ignition.

You can also try to tap the key with a small hammer, while it's in the ignition. This can cause a small vibration that may cause enough friction to loosen the wafers within the ignition and allow them to slide in place. But, be careful not to harm the key or the ignition cylinder.

If none of the above work, you need to contact a locksmith to test it out. It could be that the key has been damaged in the ignition, or it may be time to replace the whole thing. If the problem is with the key, a locksmith can create a new key for you. If the problem is related to the ignition cylinder, the vehicle is required to be brought to a repair shop to get it replaced. These problems are usually easy to fix.

Make sure you check the steering Wheel

A simple problem that can prevent the ignition from turning is the steering wheel being locked. It can happen when a driver accidentally engages the steering wheel as they exit or enter the vehicle. This usually happens by yanking the wheel while holding it against their body. It could also happen when a passenger in the rear seat is unable to stop the vehicle and engages the brakes when they exit the vehicle.

Fortunately it's an easy fix and does not require a trip to locksmiths or mechanics. First, ensure that the shifter is either in Park or neutral. If it's not, push or pull the shifter slowly until it shifts into one of these positions. You must also turn on the handbrake or press the brake before turning the key.

If the wheel isn't locked an inspection of the steering column will reveal whether the key has been engaged with the lock. A small "Lock' label is usually located in the lower area of the ignition circle. It is easily removed by gently jiggling the lock or pulling on it with moderate force. It is important not to apply too much force, as this could cause damage to the key or break off a wafer inside the lock cylinder.

Another option is using a spare key to see if it can disengage the lock. This could indicate that the original key is worn out and no more able to engage the wafers inside the lock cylinder. If this is the situation the locksmith at Karl Chevrolet Webster City will be able to make an appropriate replacement key.

If the new key won't engage, a quick spray of oil that penetrates can assist. Simply spray a tiny amount around the ignition and inserted keyhole, then jiggle or tap it lightly until it starts to work. If this does not work, you'll likely have to visit an expert at your local auto dealer. They can provide you with a replacement key and replace the ignition cylinder, if required.

Check the Key

If you're unable to get your key to turn on the ignition, it is possible that there is a problem with your key. Try taking off any foreign material on the key (lint or adhesive from packing tape, etc). You can also try rubbing alcohol or Goo Gone on the key to see if this can help.

If the pins within the lock do not move correctly when you insert your key, it's possible that they are stuck. If you have a spare key to test, try placing it in the ignition and gently sliding it back out. You should be capable of hearing and feeling the pins move inside. If you don't feel any movement, you could lubricate them with graphite powder. You can purchase graphite in small tubes that can be applied directly to the keyhole. This will help the pins slide into place as you insert the key, and will prevent them from getting stuck.

A more serious issue is that it has become damaged or worn and is unable to connect the internal pins of the ignition lock repair cylinder. This can cause the ignition cylinder to not turn and stop you from starting your car. In this instance you'll have to take your vehicle to an auto repair shop or locksmith for service.

If you're able to turn your car with a spare key, and you have eliminated any problems with the battery or steering wheel, it is possible that the ignition cylinder is worn out. Try to open the lock by using a blunt screwdriver or a handle of the hammer. Do not use the head. Gently tapping on the cylinder will often free it, allowing you to turn your key and start your vehicle. If this doesn't work, you'll need to have your lock cylinder changed by a mechanic.

Check the Ignition Socket

The ignition socket is where your key is inserted and slides out of place when you insert it. Most of the time, it gets filled with debris or simply due to wear and tear. Try putting some silicon lock lubricant (like WD-40) into the ignition to make things move forward.

You can also use a small hammer, and tap gently on the inside of the ignition to loosen or reset the pins that are out of alignment. Be careful not to overdo it or you may cause serious damage to the ignition switch.

Before you try this, make sure the car key ignition replacement near me's gearbox is set to neutral or park. Many newer cars have a system that can stop the steering wheel from turning when it is not in park or neutral that can stop the key from being turned into the ignition.

If you have tried all of these steps and your key still won't turn, it is possible that the ignition housing has to be replaced. It is important to know that different vehicles have different procedures for replacing the ignition cylinder.

Generally, this involves removal of the plastic cover which covers the steering column and ignition assembly. To remove this, you will need to first adjust the tilt-wheel to the lowest setting and then unscrew any fasteners holding it in place.

After removing the cover you'll have to remove the old ignition cylinder from the steering column. Then, you'll need to compare the new ignition cylinder you purchased with the one that was removed to make sure that they are the same. After this step is completed the new ignition cylinder can be installed in the same way that the previous one was removed.

It is possible that, despite our best efforts, an ignition can be damaged and require to be replaced. It is suggested that if this happens, you call a Tempe Locksmith. A locksmith will assist you in selecting the right replacement and then install it correctly, so that your car ignition lock (how you can help) can start again.