• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC windows are a great choice for modern homes. They are easy to maintain and are durable and long-lasting. They are not susceptible to decay or rust as aluminum and timber.

It is essential to clean and oil UPVC doors and windows regularly. This will reduce repair costs as well as improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows could cause severe damage to your home and may even be fatal. It is important to ensure that your windows are in good condition.

Single-pane windows are relatively simple to replace and will usually fit into the old frames very easily. If you have double glazed window repairs-paned windows that are held together by internal beading, it will be difficult to remove and replace the old panes. In this instance, it is necessary to purchase plastic spacers in order to aid in fitting the new pane into the window frame.

Wearing protective eyewear and thick gloves is a must when you are planning to remove the glass yourself. You should also lay down a drop cloth before you begin working on the window panes so that any shards fall on the fabric and not on the floor which could cause them to be trampled.

It's a good idea to seal the gap after the glass has been removed. This will stop water and drafts from entering your home until a professional comes out to repair the window. It also acts as a barrier, deterring any intruders from getting access to your home. If the gap is large, window repairs you might think about the security door with an integrated window, since this will offer the best of both worlds.

2. Sagging

Upvc is a long-lasting energy-efficient, cost-effective and economical alternative to timber sash windows. However, over time, they are susceptible to a range of issues like sliding. A window that is sagging can cause problems with light, draughts and even security. It's important to take action immediately if you realize that your uPVC windows are sagging.

Repositioning the hinges can aid in fixing a window which is sliding. To do this, you'll need to open the window to get to the frame. Then, you can remove the top and bottom hinges using a screwdriver and adjust them clockwise or counter-clockwise. Once you've adjusted the hinges, shut your window and test it for fitting. If you're satisfied with the fit, tighten the screws to ensure that they remain in position.

If you can't reposition the hinges, you might need to replace the seal. Rubber seals can dry out and lose their elasticity with time, causing them to loose their elasticity. It is essential to replace your seal as soon as you can in order to ensure that your uPVC window watertight and draughtproof.

uPVC handles can also become loose. Often this is due to screws that have become loose over time. However, it could be due to the fact that the handle mechanism has worn out. Luckily, it's not difficult to repair the loose uPVC window handle yourself. The first step is to close your window and do a test to ensure that it fits. The joint at the corner of the sash should be aligned with the joint on the casing. If it doesn't then you can make use of a screwdriver to loosen the handle and turn the mechanism back into position.

3. Water Leaks

If you wake up to wet floors and mouldy walls each time it rains, it's crucial to take action. Water leaks through windows can cause structural damage to your home and hinder your ability to control the temperature inside your home. The most common reason for leaking uPVC windows is that the sealant surrounding the frame is damaged or is missing.

This is a relatively easy fix that can be done by any competent DIYer. Depending on the severity of the problem the caulking that was used up may need to be removed before a new layer can be applied. It is essential to remember that when it comes to uPVC window repairs, you should not be tempted to apply too much caulk' as this will only make the area harder to clean and can reduce your energy efficiency.

It is essential to ensure that any drainage holes are clear of debris and that the sill pan is placed properly so that it drains away from the window. In more serious cases you might need to consider replacing the window.

Other signs of long-term water leakage are sills that are rotten and the appearance of black spots of mold on the walls near the window. This fungus thrives in humid conditions and can propagate quickly throughout the home.

It is also important to keep in mind that if the leak is coming from between the glass of your double glazed windows it may be more likely to be a problem with the glass seal, rather than the frame or sliding. Again this can easily be corrected by a uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault if your uPVC window repair is difficult to open, or if it blows open with a breeze. These are easily repaired by any skilled DIYer and can usually be completed in a matter of minutes.

Like any mechanical part hinges are prone to wear out over time. It's easy to change the hinges on a window, but it's easier if someone helps you hold the frame.

Make sure that the uPVC hinges are closed and open in the right direction. You can check this by looking for the arrow on each hinge, this shows which way the window should open.

Faulty window hinges could be the result of incorrectly opening the window in a particular way or due to poor installation at the factory. Sending us photos through our website can often solve the issue. We are more than happy to offer advice.

It is also crucial to grease the hinges on a regular basis. Applying an engineering lubricant that is light to the hinges is a great method to accomplish this. We recommend using a lubricant that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It can also reduce the chance of windows getting stuck and stop corrosion. Ideally, you should do this once a year. WD40 or other solvent-based lubricants should not be used since they can damage your uPVC windows.

5. Draughts

Draughts can be caused by a variety of different things. The hinges, also due to wear and tear may become displaced, which will cause an opening to appear where the sash meets the frame. If they are beyond repair, it might be necessary to get them re-aligned. The second is the interlock, which is located on the hinge side of the window, may also be misaligned, and window repairs again it's possible to just give them a clean but in certain cases, it may be necessary to have these replaced.

The seals may wear out or get damaged over time, allowing air to escape. Replacement of these with high-quality weatherstripping is a good way to keep draughts at bay. Replace the windows made of Upvc with low-emissivity lenses. This will help to regulate indoor temperatures, and reduce draughts.

Another, and most effective ways to cut down on the draughts in your home is to use an draught excluder. These are typically made of fabric that are filled with some sort of filler and can be placed on the windowsill on top. They will keep your home warm by blocking cold air.