• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Replacement Door Handles

The handles on your doors get worn out over time and need to be replaced. It is essential to be able to match the dimensions of the handles you have previously replaced when replacing them.

The top screw's location the lever, and the keyhole sizes are the three measurements you have to check. Use the size guide to aid you.

Inline Lever/Lever

A lever/lever door handle is a contemporary handle that can be put in on doors that are new or replacement. This style door handle is available in a wide range of styles and finishes. This handle is offered by several manufacturers including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The handles made of uPVC/Composite are made of tough materials and are ideal for multi-point lock doors that need a heavy-duty design. The handles are inline and they utilize the same screws and spindle to fix them. They can be easily installed on a new or existing uPVC/composite door handles door.

The handle can be positioned and angled to fit any user. The handle has been endurance-tested to 200,000 cycles. This helps to ensure that the finish is of high quality and performance over time. The sprung lever is also adjustable to fit a wide range of locks. This is particularly useful for doors with narrower frames, where the cylinder is further back. A shortened lever can also be used for doors with latches that can be opened by the thumb located on the inside.

Lever Pad

A Lever Pad door handle made of upvc functions differently from lever-type handles that are found on the majority of doors. These handles are operated by one spindle or two spindles, inline or offset. They are usually employed on UPVC double glazed door handle glazed doors and are available in a variety of variations and styles.

The handles for double glazed doors have been tested to the minimum of 200k cycles and are available in a variety of finishes, including White, Silver, Chrome & Gold. The finish meets BS EN 1670:2007 Grade 5 and is also resistant to corrosion, which gives the handle a high level of durability and performance for its intended use.

All of the UPVC handle lever pad styles come with screws and a spindle which allow them to be fitted on a new or existing uPVC door. The backplate fixing centres of 211mm allow for a larger size handle that can often be a benefit when replacing a faulty or worn multi-point door lock mechanism. The handle levers come with springs, which can solve the problem of door handles that move out of horizontal position when they are not being used.

It is crucial to ensure that the PZ dimensions for both the multipoint lock as well as the uPVC doors when choosing a replacement UPVC spindle and handle. This measurement is often known as the handle centre or 'cylinder centres' and is a critical aspect of matching up the correct handles.

After you have identified the proper PZ size it is important to make sure that the push and lever pads are designed to fit the American with Disabilities Act compliant handles that you need for your door. They are typically round or square with an internal lever and an external push pad.

The majority of the UPVC Lever Pads we offer are sprung. This means that they return to a horizontal position after not in use instead of hanging, and possibly sticking in the frame. This stops draughts from entering the building. The majority of UPVC lever pad handles are available in left and right handed models that allow them to be put on either side of doors.

Euro Cylinder

Cylinder locks are commonly used on uPVC doors, but can also be used on other types of door. They work by using a key that unlock a cylinder that is then revealed with pins that can be aligned to those in the lock body and allowing them to turn an revolving cam, opening the door. euro door handles cylinders can be fitted with up to six pins. Doors that are internal and external require different levels of security.

The choice of the correct cylinder is vitally important; this is dependent on the way your doors and handle are utilized. External doors, for example should be equipped with higher security cylinders while doors inside can be secured using a standard cylinder. Certain cylinders are equipped with additional features that increase security, like anti-drill or anti-bump properties.

A euro cylinder needs to be properly measured to ensure that it is the right size for your door. The cylinder should be measured from the hole in the center of the fixing screw to each end of the cylinder, including the thumb turn if you have one. It is best to do this with the lock in place, but if this is not feasible, you can take it off and remove it to measure. It is important to not have a extension of the cylinder beyond the handle or escutcheon. This could make it susceptible to lock snapping attacks.

Most newer cylinders have been made with bump and anti-drill features included in their design. They are designed to minimize attack chances by forcing the cylinders to turn in a new direction. This can help to deflect attacks and protect your door.

There are also cylinders that have been designed to withstand snapping. This is a growing method of attack on cylinders which is where the break line of the lock is targeted using a special tool to break the front of the cylinder to allow the door to be opened. This is faster and less difficult than opening the door with multipoint locks and leaves little evidence of a break-in which could hinder an insurance claim.

Spring Cassette

The spring cassette is positioned in the base of your door handle backplate, providing a spring solution to return your multipoint lock handles to their rest position after use. Previously a lot of these types of handle did not have a spring integrated into them, and without it they tend to droop or drop when the locking mechanism is disengaged. Adding this simple component is among the best methods to correct this and it is also a great way to prevent your doors made of upvc from becoming stuck in either closed or open position, as they are not always easy to close manually.

These spring cassettes were created to be used with a sprung multipoint lock. They won't work with unsprung handles and you'll have to cut a hole in the backplate to allow them to fit. (Please see the image for a technical diagram). They are a replacement for broken or missing cassettes in the door handle backplate of various kinds of uPVC doors. They are available as a single unit. They come with a square cut out that can accommodate an 8mm shaft.

These spring cassettes are an excellent cost-effective way to fix the problem of door handles that are sagging. They are simple to put in and will increase the life span of your uPVC doors. Contact us for more information on our range of uPVC accessories and spares. We are always ready to offer expert advice and to assist you.