• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Fiat 500 Replacement Key Fob

It might be time to replace the battery if your 500 remote key fob is not working. However, if you replace the battery and it is still not working, then the problem may be elsewhere.

At United Locksmith, we specialize in the creation of new keys for classic automobiles. We have the tools as well as the parts needed for this service.

Dead Coin Battery

A dead battery is the primary reason for your fiat van key replacement 500 keyfob not locking or unlocking the doors. The key fob contains an in-built battery which will quickly drain when it isn't frequently used. If your remote began to show signs of weakness such as a loss of range and stopped working completely the battery could be dead.

Metal clips hold the battery in in the key fob. If the clips are loose, it can cause problems with contact, which can prevent the remote from receiving power. Make use of a flathead screwdriver to pry open the retaining clip and remove the old battery. Make sure you use an alternative battery that has the same kind of voltage, size, and specification as the original battery.

The key fob may also be damaged or corroded by exposure to water. Even a small bath in soapy water could cause damage to the electronic chip inside. It's best to keep your key fob in a dry location.

Water Damage

If your key fob isn't functioning correctly, it could be due to water damage. Key fobs have rubber seals that protect them from being damaged by a light rain or splashes of water, but it is essential to keep your keys out of the ocean, pool, and the washing machine!

The key fob comes with an electronic chip that sends a signal car's immobilizer system. This is the reason why your 500 can start or lock, however should the chip become saturated, it won't be able to longer function.

Try cleaning the inside electronics of your keyfob using isopropyl alcohol, or Fiat 500 Replacement Key Fob an electronic cleaner to determine whether they're still working. It is best to replace a key fob if it's submerged into salt water rather than attempting to repair it yourself.

A replacement fob could cost you a little bit but it's far less expensive than paying to have your Fiat 500 towed to a dealer and repaired there! Plus, you can do it yourself in a few easy steps. Make sure you have the correct type of battery before you attempt to open your keyfob. This task is much easier than it looks, and you can find step-by-step directions on the internet for nearly any key fob for your car.

Faulty Chip

The chip inside the key fob communicates with the immobiliser on your vehicle to ensure that the vehicle will only start when proper keys are inserted. If the chip is damaged, or corrupted in any way it will not start.

A chip that is defective can happen due to many reasons, but most commonly due to water damage or an unresponsive battery. It is best to delegate the work to a professional locksmith who can replace the chip quickly and at reasonable cost.

If your key fob fails to function after exposure to clean water from the tap or rain, remove the battery and wipe down the electronic component with a paper towel to ensure it's dry before putting it back in. If the key fob isn't working it's likely to be a fried chip and will need to be replaced.

A few people turn to their dealer when they are in need of an entirely new Fiat key fob, however it can be a expensive option. If you're looking for a low-cost solution to get your Fiat key fob fixed make sure you contact United Locksmith. We have the equipment and know-how needed to repair your Fiat key fob in a timely and professional manner.

Faulty Receiver Module

fiat 500 car key replacement key fobs transmit a signal to the vehicle, which will unlock and lock doors (and Fiat 500 Replacement Key Fob start the car if it has an automatic transmission) up to 50 feet. There are a few reasons why a fob could not function. This includes a dead coin-battery or water damage, worn out buttons, a receiver issue, signal interference, or malfunctioning chips.

If the fob has been placed in a pocket that been subject to extreme trauma, like being dropped on hard floor or being washed in the washing machine and it isn't capable of communicating with the car's Body Control Module (BCM). This is because the BCM is secured and will only accept signals from a genuine key and not another.

It is necessary to replace the fob in case this occurs. A professional locksmith can handle every aspect of the replacement procedure, including programming a new one for the 500. In fact, they'll offer you a clone key that functions exactly like your original fob (and costs only a fraction of the cost).