• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps allow your pet leave and come at their own pace without you having to let them in or out. They also prevent your cat from urinating inside the house.

Installing a cat flap into a upvc door panel is much easier than in a glass door, however it does require some skills and the appropriate tools.

Take a measurement of the door

Installing a cat flap on a door can be tricky but as long as you choose the right type of cat flap make sure you take your time and follow the steps provided it shouldn't be too difficult. We will show you how much to install a cat flap to mark the shape and use an jigsaw to cut the door's opening. Then we will finish the job by attaching the flap. This will ensure that the flap stays in place and shields the door from wind and rain damaging the door.

To determine the size of the cat flap that you need, measure your pet's width. This will enable you to select a cat flap that is large enough to allow your pet to enter the house and exit without needing to open the door each time.

Once you have the measurements, you can mark the location on the door where the template should be positioned, usually, this is done using an X. However, some kits include drawings that show the location to drill, if you have one, then attach it to the door and draw a line around the door. If your door has moulding or a sill at the bottom, make sure you leave enough space between your cat and these elements.

Next put on your eye protection as well as a dust mask, and using a jigsaw start cutting along the line that you've drawn in, but don't push the blade too hard because this could cause it to cut more quickly than you want it to. If you own a set square then make use of it to verify that you're cutting properly and to ensure that the hole is in a rectangle shape, once you are satisfied with this you can begin to take off the rest of the door material.

Draw a Line

The cat flap is a great method to allow your pet to go in and out without having to worry about them coming in with guests or leaving unwanted gifts inside the home. It also prevents draughts, and helps keep your home's temperature in check. However, installing an animal flap on your door might seem like an intimidating task for those who haven't done it before, leading many to hire a professional joiner or carpenter to complete the task. This is an option but you can do it yourself if the tools are right and the steps are followed.

This is much simpler to do on a wooden door, but it is possible with uPVC. However, you must be careful not to scratch the doors with cat flap since this could make it impossible to claim your warranty. The first step in the process is to take measurements of the door, making sure that it can accommodate the new cat flap. This should be simple enough for a standard uPVC door, but you may require more care if using an insulated or composite type of door since these are more difficult to cut than solid uPVC panels.

Next, you will need to determine the belly height of your cat. This is the height between the floor and the bottom of your cat's stomach. It is important to locate an area at the entrance that allows your cat to move through easily. Once you've got the information, you'll need to mark the area with a spirit-level and a pencil so you are certain that the hole will be suitable for your cat.

After you have marked the area, it is time to cut out the hole. It is crucial to take your time and use a jigsaw ensure the cuts are smooth and clean, not rough and uneven. This could cause damage to your door. You should also remember to wear safety glasses and a dust-proof mask whenever using the jigsaw, as breathing in the dust can be dangerous to your health. Once you've finished cutting the hole, you will require sandpaper to smooth the edges so that the cat flap is easily inserted into the hole.

Make a hole

The process of fitting a cat flap into an existing door panel or double glazing sealed unit can be difficult. You might be tempted to tackle the job yourself, but unless have expertise in DIY, it's likely to be best to have an expert to complete the job for you. A faulty job can not only be unsightly, but also pose an security risk. It could allow cold air in when the cat is outside and hot air to escape when the cat is inside.

Mark the hole position on the door using a pencil and spirit level. This will ensure that it is correctly positioned and is flush with the rest of the door. Make sure you have a piece of sandpaper at ready to smooth out any rough edges.

Wear any safety gear you need to work with a power tool. If you're concerned about the noise, you can get a jigsaw with a cord that is more quiet and easy to use.

It is best to only remove the material required to make the cat flap. A little bit of extra material is required to increase the thickness of the the flap, but removing more than that could cause issues and harm the frame of the door.

A upvc door may contain a metal frame or panel that will interfere with the microchip cat flap and if this is the case you'll need to cut an over-sized hole to ensure that the metal does not come into contact with the the cat flap, if this is done, it is important to fill in the oversize gap and make it watertight.

If you are fitting a cat flap into an upvc door or a double glazed windows with a frame made of metal, you will need to speak to a specialist who can provide you with a new glass pane with the hole for the cat flap in it. This is less expensive than fitting cat flap insulation flap in upvc door panel (Peatix link for more info) a cat flap inside an existing pane that was not designed for this purpose.

Fit the Flap

Cat flaps allow your pet the freedom to go and come whenever they like, allowing them to relax in the home whenever they want to. If you have an uPVC front door, it might be difficult to install a cat flap. This is particularly true in the event that you don't own a glass panel that can be cut. If you're willing to buy and install a replacement upvc door panel with cat flap half-glazed upvc door panel cat flap panel, it's possible to install a cat flap to the doors. It's not as simple as simply cutting a hole through the door, however there are a few things you'll need first to make sure it's safe.

A composite, uPVC, or GRP door panel usually has an flimsy plastic outer layer that is bonded to a soft, polystyrene core that is insulating. The material is extremely fragile and care must be taken when cutting through it to avoid causing damage. This kind door comes with a template that you can use to make the hole.

After you have marked out the hole in your front door, it's time to install the cat flap. You can pick from a variety of models, ranging from simple push-button models to microchip activated ones that only let your pet in. But, regardless of the kind of cat flap you choose it's important to make sure that your cat can use the flap without becoming trapped in the weather.

It's a good idea to choose a circular fitting rather than one that is square, because circles can be more securely cut into the door glass. This is because square holes make the glass more susceptible to cracking when drills are used on it. This is also a safer option since you don't have to drill into the toughened glass that could break and hurt your pet or your family members. This is especially important if there are elderly or children living in your home who might be injured by glass shattering.